Low reading guages

Batteries, Alternator, Wiring, Lighting, etc. (Please discuss ignition problems in the Engine category)
Post Reply
Message
Author
aidanfisher
Newbie
Newbie
Posts:6
Joined:Sun Dec 17, 2017 3:22 pm
Location:Manchester
Low reading guages

#1 Post by aidanfisher » Wed Jan 10, 2018 8:02 pm

When I bought OME 87L both the temp gauge and the fuel tank gauge were reading something like less than half they should.

I changed the temp sender--no difference. Today I changed the voltage stabiliser--still reading the same.

Any suggestions as where to go now?? Help!

User avatar
Dave B
Senior Member
Senior Member
Posts:995
Joined:Thu Dec 27, 2007 8:37 pm
Location:Wigan,Home of the mighty Warriors

Re: Low reading guages

#2 Post by Dave B » Wed Jan 10, 2018 8:42 pm

Try an additional earth with good clean contacts to the (black wire) negative circuit at the rear of the instrument panel.

By the way, dont forget the Lancashire group meeting a fortnight tomorrow 25/1/18. :)
New Hall Tavern, Cuerdale Lane, Samlesbury, Preston PR5 0XA.
01772 877942
Club Member 2035
1970 2500 Mk2 in pimento red[/col
Toyota Avensis T4 Tourer

tony
Senior Member
Senior Member
Posts:799
Joined:Sun Jun 14, 2009 5:35 am
Location:New Zealand

Re: Low reading guages

#3 Post by tony » Thu Jan 11, 2018 3:48 am

When I had this problem a few years ago I found the earth terminal had dropped off the back of the speedo.
Tony.
1976 2500 TC. converted to S specs.

Lots of bits

1999 BMW Z3.
2006 BMW 325ti.
Hopefully not needing too many bits.




.

aidanfisher
Newbie
Newbie
Posts:6
Joined:Sun Dec 17, 2017 3:22 pm
Location:Manchester

Re: Low reading guages

#4 Post by aidanfisher » Thu Jan 11, 2018 1:35 pm

Just tried an new earth wire --back of speedo to body panel --just the same result!!

So now need to do some serious digging--snag is its b--y cold working out there!

Haven't forgotten about the 25th!

Mike Stevens
Site Admin
Site Admin
Posts:3593
Joined:Mon May 08, 2006 9:50 pm
Location:South Oxfordshire, UK

Re: Low reading guages

#5 Post by Mike Stevens » Fri Jan 12, 2018 5:24 pm

I guess you need to measure the voltage coming out of the regulator. If it's an original mechanical type it should wander about a bit but average to 10V ish. I think you've fitted a new one so that will (probably) be electronic so a steady 10V. Anything less than this is a fault as is much above 10V too!

As your gauges (temp and fuel) are reading low I'd expect the regulator output to be low. If it is, try disconnecting one or other (or both) leads from the regulator to the gauges. Maybe there's a fault in one which is pulling the 10V line down. Hopefully this will help you fault find!

Good luck,

Cheers,
Mike.
(South Oxfordshire)
Register Member No 0355
1971 2.5PI Saloon Sapphire blue
1973 2.5PI Saloon rust some Honeysuckle
1973 Stag French blue
(1949 LandRover was blue should be light green!)

User avatar
Alec
Senior Member
Senior Member
Posts:2511
Joined:Sat Feb 07, 2004 7:23 pm
Location:Oswestry, Shropshire

Re: Low reading guages

#6 Post by Alec » Sat Jan 13, 2018 12:05 pm

Hello Aidan,

if your voltage stabiliser is the original bimetal type, ensure that the case is properly earthed also. However as Mike says, if you can do a voltage check that will be very useful. (Analogue meters are better for the bimetal type.)

Alec
0465

MK1.5 2.5 P.I.
Jaguar MK 2 (Long term restoration.)
Hymer 564 Motorhome.

aidanfisher
Newbie
Newbie
Posts:6
Joined:Sun Dec 17, 2017 3:22 pm
Location:Manchester

Re: Low reading guages

#7 Post by aidanfisher » Fri Jan 19, 2018 8:48 pm

Thanks for all the advice chaps--jobs on hold until this perishing weather lets up a bit. I have a trusty AVO meter so should be able to get some sensible readings.
Wish me luck!

Mike Stevens
Site Admin
Site Admin
Posts:3593
Joined:Mon May 08, 2006 9:50 pm
Location:South Oxfordshire, UK

Re: Low reading guages

#8 Post by Mike Stevens » Tue Jan 23, 2018 10:20 am

An Avo would be the ideal instrument for measuring the voltage output. When you do, do check with the negative lead in various places, (speedo, voltage stabiliser, car body etc). All should read the same, but if they don't, that would point to the problem.

Let's hope it warms up a bit. And dries out!

Cheers,
Mike.
(South Oxfordshire)
Register Member No 0355
1971 2.5PI Saloon Sapphire blue
1973 2.5PI Saloon rust some Honeysuckle
1973 Stag French blue
(1949 LandRover was blue should be light green!)

torque2me
Senior Member
Senior Member
Posts:310
Joined:Thu Aug 13, 2009 12:52 pm
Location:Hatfield

Re: Low reading guages

#9 Post by torque2me » Mon Jun 10, 2019 9:36 am

aidanfisher wrote:
Wed Jan 10, 2018 8:02 pm
When I bought OME 87L both the temp gauge and the fuel tank gauge were reading something like less than half they should.

I changed the temp sender--no difference. Today I changed the voltage stabiliser--still reading the same.

Any suggestions as where to go now?? Help!
I hope this is not another "no final outcome posted" subject?

Was there an outcome?

Kev

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests