Barn Find Triumph Pi
-
- Senior Member
- Posts:288
- Joined:Tue Nov 19, 2013 8:50 pm
Hello all! just finished up the rear arch - wing.
Fitted a door and the gaps are good. A little distortion at the bottom corner, however there was substantial braze filling here, so I guess that's the way it is.
I've done the drivers floor, a piece in the boot and part of the inner arch above the suspension mount. This was a complete nightmare very much a wobble moment. Under the arch a helmet, gloves, clamps Mig welding torch the fabricated part and I told the cat he had to wait a minute. Anyway I will upload pictures as soon as. Been busy this weekend with the other sill, much the same as the other side.
Thanks for all the replies just got to keep the momentum up. Slightly harder now the good weather is here. The temptation to have a brew and sit back and look at what's to be done is rife!
Fitted a door and the gaps are good. A little distortion at the bottom corner, however there was substantial braze filling here, so I guess that's the way it is.
I've done the drivers floor, a piece in the boot and part of the inner arch above the suspension mount. This was a complete nightmare very much a wobble moment. Under the arch a helmet, gloves, clamps Mig welding torch the fabricated part and I told the cat he had to wait a minute. Anyway I will upload pictures as soon as. Been busy this weekend with the other sill, much the same as the other side.
Thanks for all the replies just got to keep the momentum up. Slightly harder now the good weather is here. The temptation to have a brew and sit back and look at what's to be done is rife!
Last edited by Tinsmith_Skippy on Fri Jul 14, 2017 4:32 pm, edited 3 times in total.
-
- Groupie
- Posts:47
- Joined:Thu Jan 01, 1970 12:33 am
- Contact:
Re: Barn Find Triumph Pi
Blimey, what a save!
It seems like you've got an awful lot of work to do there but I can see that you know what you're doing and it's looking good...
This is one very rare car so it's great so see it being saved!
Good luck with the project, I cannot wait to see more updates...
It seems like you've got an awful lot of work to do there but I can see that you know what you're doing and it's looking good...
This is one very rare car so it's great so see it being saved!
Good luck with the project, I cannot wait to see more updates...
-
- Newly registered
- Posts:1
- Joined:Sat Jan 03, 2015 10:26 pm
Re: Barn Find Triumph Pi
very nice work indeed, as a panel beater to trade this is the minimum standard that should be applied in renovating a motor, keep up the good work....
Re: Barn Find Triumph Pi
As someone with no experience of any type of welding, I have been reading your posts with a great deal of interest (and admiration!!).
Haven't seen any recent posts of how you are progressing....any further developments with the P.I. restoration Ross?
Haven't seen any recent posts of how you are progressing....any further developments with the P.I. restoration Ross?
Register Member no. 1596
1967 Mk1 2000 in Gunmetal Grey
1969 Mk1 2000 in Royal Blue
1970 Mk2 2000 in Valencia Blue
1972 Mk2 2.5 PI in Triumph White
1973 Mk2 2.5 PI in Sienna Brown
1976 Mk2 2500S in Carmine Red
1967 Mk1 2000 in Gunmetal Grey
1969 Mk1 2000 in Royal Blue
1970 Mk2 2000 in Valencia Blue
1972 Mk2 2.5 PI in Triumph White
1973 Mk2 2.5 PI in Sienna Brown
1976 Mk2 2500S in Carmine Red
-
- Senior Member
- Posts:288
- Joined:Tue Nov 19, 2013 8:50 pm
Re: Barn Find Triumph Pi
Hello progress on the car has stalled due to the birth of my first child Angus who was born 2 weeks ago. Before his arrival I had to redecorate some rooms in the house. Now time is a little occupied with the little one, the day job and catching up on lost sleep. However I have completed repairs to the drivers side floor, small patch in the boot and the passenger side sill before his arrival but since then I haven't had the time to post the pictures. Anyway once he has settled down I will continue the restoration but I'm trying to save up for an English wheel so I can repair the front arch bowls and this going to take some practice. The repairs to the nearside rear arch are going to require a lot of attention, this is going to take time due to the rotten floor where the fuel pipes have gathered wet mud, rotting this area serverley . Once again thanks for the interest and I'll keep the updates coming.As someone with no experience of any type of welding, I have been reading your posts with a great deal of interest (and admiration!!).
Haven't seen any recent posts of how you are progressing....any further developments with the P.I. restoration Ross?
Re: Barn Find Triumph Pi
Hello Ross,
consider a shrinker/ stretcher as that takes far less room and is also much cheaper, unless of course, if you are planning a lot of panel forming?
Here's a picture of a spare wheel patch panel I made for my MK 1 on such a device. Being face on it doesn't show the curvature too well but I was very pleased with how it formed, especially as I had not long bought the tool.
Alec
consider a shrinker/ stretcher as that takes far less room and is also much cheaper, unless of course, if you are planning a lot of panel forming?
Here's a picture of a spare wheel patch panel I made for my MK 1 on such a device. Being face on it doesn't show the curvature too well but I was very pleased with how it formed, especially as I had not long bought the tool.
Alec
0465
MK1.5 2.5 P.I.
Jaguar MK 2 (Long term restoration.)
Hymer 564 Motorhome.
MK1.5 2.5 P.I.
Jaguar MK 2 (Long term restoration.)
Hymer 564 Motorhome.
- TedTaylor
- Senior Member
- Posts:1670
- Joined:Sat Dec 06, 2008 11:27 pm
- Location:Forest of Dean (Gloucestershire)
Re: Barn Find Triumph Pi
Congratulations over the new born Ross. We can accept this as a valid reason for a hold up in the work .......
MUT
MUT
Member 4473 1990
1964 2000 period rally look alike AFH 849B
Morris 1800 London-Sydney/Monte/WCR NAM 616G
Mk1 PI Estate SCG 115G
2500 Estate WDE 76K RBRR 2014
1964 2000 period rally look alike AFH 849B
Morris 1800 London-Sydney/Monte/WCR NAM 616G
Mk1 PI Estate SCG 115G
2500 Estate WDE 76K RBRR 2014
-
- Senior Member
- Posts:492
- Joined:Thu Jan 01, 1970 12:33 am
- Location:cardiff
Re: Barn Find Triumph Pi
hi ross
huge Congratulations on the arrival of angus
huge Congratulations on the arrival of angus
Re: Barn Find Triumph Pi
Yes, my congrats also! Your newborn (Angus) will be obviously be first on your list of activities, but hopefully your reborn (PI) will carry on not far behind!! Look forward to seeing further pics.
Register Member no. 1596
1967 Mk1 2000 in Gunmetal Grey
1969 Mk1 2000 in Royal Blue
1970 Mk2 2000 in Valencia Blue
1972 Mk2 2.5 PI in Triumph White
1973 Mk2 2.5 PI in Sienna Brown
1976 Mk2 2500S in Carmine Red
1967 Mk1 2000 in Gunmetal Grey
1969 Mk1 2000 in Royal Blue
1970 Mk2 2000 in Valencia Blue
1972 Mk2 2.5 PI in Triumph White
1973 Mk2 2.5 PI in Sienna Brown
1976 Mk2 2500S in Carmine Red
Re: Barn Find Triumph Pi
Um this pails my car bodywork into showroom condition. As in I thought mine was rough - at least I had something to work on - you only had dust.Maybe I'm being fussy. Nothing can take away the mammoth effort you have gone to there. I wouldn't know where to start.Top marks from a 2000 enthusiast,but I'm miles away from someone like you.
Member Number 7392 04/07
1975 TRIUMPH 2500S AUTO ESTATE IN BRG!
DON'T TIDY UP - LEAVE IT WHERE IT FELL!!
1975 TRIUMPH 2500S AUTO ESTATE IN BRG!
DON'T TIDY UP - LEAVE IT WHERE IT FELL!!
Who is online
Users browsing this forum: No registered users and 3 guests