Door pillar side repeaters

Message

#1 Post by **TedTaylor** » Sat Feb 13, 2016 11:42 pm

Does anyone have any spare door pillar side repeater lenses (or complete units) for the Mk1 or Mk2 saloon/estate please?

I am primarily after the flat type (not the later domed type).

Thanks

MUT

#2 Post by **johnconradlee** » Mon Feb 15, 2016 12:39 pm

Rummaging in a box I found a pair of the later thinner flat ones at Stoneleigh. Think I paid £20.00 (unfortunately the seller knew what they were). These are now on the car so I can't sell them to you.
Stoneleigh is 21st February this year. If you're not going up this year I can have a look for you to see if I can find any more.

#3 Post by **wild bill** » Mon Feb 15, 2016 6:44 pm

TedTaylor wrote:Does anyone have any spare door pillar side repeater lenses (or complete units) for the Mk1 or Mk2 saloon/estate please?

I am primarily after the flat type (not the later domed type).

Thanks

MUT

I also could do with a couple of new ones if there are any about,
Thanks in anticipation,
Bill.

#4 Post by **englishbull** » Tue Feb 16, 2016 7:50 am

Gold dust!!!!!!!! especially drivers sides of all four types.

I have two NOS N/S ones and some decent o/s ones.

I have just sold a very good pair to a guy doing a resto on a MK1..........

#5 Post by **Mike Stevens** » Tue Feb 16, 2016 12:38 pm

I have a box of those somewhere. I'd better go and see what's in there!

Cheers,
Mike.

#6 Post by **david_lall** » Tue Feb 16, 2016 12:49 pm

Is re-manufacture beyond realistic cost?

#7 Post by **stuart490** » Tue Feb 16, 2016 2:39 pm

A few years ago Chris Witor asked (in SixAppeal I think) for those prepared to purchase remanufactured lenses to e-mail him. I recollect that it was the flat ones he was proposing to remanufacture. Due to the lack of interest that was as far as it got. Perhaps the time has come to encourage him to try again? I certainly would purchase a set for my Mk1. A poll on here might help, could someone set it up - it is beyond my capability.
Here's hoping,
Stuart

#8 Post by **johnconradlee** » Tue Feb 16, 2016 3:37 pm

I emailed Chris last year about this and he replied "Tooling for lenses is over 12k, so we are looking at our options..."
As I haven't heard anything I assume it hasn't got any further. £12k does sound a lot, I'm not sure if that was all types and in both hands.

I was thinking about whether it would be possible to produce small batches by casting them in a silicone mould with resin.

#9 Post by **TedTaylor** » Tue Feb 16, 2016 4:06 pm

It was something the late lamented Spares Group were looking into until it had to fold due to lack of support.

Yes Lee I know they are difficult to find ...... I am asking in case someone has any. Want them for the two Mk1s, thin type and/or thick type, are you selling yours?

MUT

#10 Post by **englishbull** » Wed Feb 17, 2016 8:06 am

TedTaylor wrote:It was something the late lamented Spares Group were looking into until it had to fold due to lack of support.

Yes Lee I know they are difficult to find ...... I am asking in case someone has any. Want them for the two Mk1s, thin type and/or thick type, are you selling yours?

MUT

Hi Ted,

Sadly I am not selling mine due to the rarity of them nowadays and I am only selling the ones to the guy who is near completetion of his MK1.

Plus the ones I have in good nick are the very early type.
Not tellinmg how to suck eggs but the base plates do differ between MK1 PFL /FL and the late MK1 / MK2
If desperate I may have some half decent ones somewhere but will have to fish them out.

The Triumph 2000/2500/2.5 Register Forum

Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Re: Door pillar side repeaters

Who is online