Search found 177 matches
- Fri Apr 20, 2018 2:07 am
- Forum: General Discussion
- Topic: Service notes & website question
- Replies: 4
- Views: 7064
Re: Service notes & website question
Cheers John, have fired off an email to Malcolm and Jan.
- Tue Apr 17, 2018 2:14 am
- Forum: General Discussion
- Topic: Service notes & website question
- Replies: 4
- Views: 7064
Service notes & website question
A couple of quick questions:
Are the service notes still available to buy either in paper or electronic format?
Also, is there still a members only section of the website/forum? I can't see one...
Cheers
Are the service notes still available to buy either in paper or electronic format?
Also, is there still a members only section of the website/forum? I can't see one...
Cheers
- Thu Apr 12, 2018 5:24 am
- Forum: Transmission
- Topic: Slipper pads or not?
- Replies: 6
- Views: 6816
Re: Slipper pads or not?
A bit of a delay - and I nearly missed this. When I looked closely at the bearing carrier this morning there are two cracks on opposite sides of the carrier where the fork prongs sit. Looks like perhaps the lack of slipper pads has caused additional stress on the carrier which has fatigued and fract...
- Thu Apr 12, 2018 5:04 am
- Forum: Transmission
- Topic: Clutch fork
- Replies: 4
- Views: 5447
Re: Clutch fork
Do check the taper pin and when screwed home that the head of the pin is not seated on the fork, i.e. it is tight but the taper is not properly seated. I have just done mine and I had to relieve the head on my lathe so that it does not bottom on the fork. If the taper is not tight there is more cha...
- Wed Apr 11, 2018 8:38 pm
- Forum: Transmission
- Topic: Flywheel spigot bushing
- Replies: 14
- Views: 14637
Re: Flywheel spigot bushing
Cheers johnnydog - that was my understanding of the fitment of the bushing so good to see I'm heading in the right direction. I have the bushing on order and the 'box is already out so hopefully fitting the new one will be a relatively simple affair. I have a cut off input shaft for centring the clu...
- Tue Apr 10, 2018 11:02 am
- Forum: Transmission
- Topic: Clutch fork
- Replies: 4
- Views: 5447
Clutch fork
Does anyone have any tips for getting the clutch release fork back onto the cross shaft? Mine is very tight and took a lot of pulling and wiggling to get off - I'm not sure I'll be able to apply the same force pushing as I did pulling. The Haynes manual does state that the fit can be "very tight" - ...
- Mon Apr 09, 2018 11:04 am
- Forum: Transmission
- Topic: J type overdrive wiring
- Replies: 5
- Views: 6167
J type overdrive wiring
Regardless of whether a relay should be fitted (I intend to fit one), an I right in thinking that the factory wiring for the J type overdrive was a postive feed from the reverse light circuit running to one terminal of the inhibitor switch then from the other terminal of the inhibitor switch to one ...
- Fri Apr 06, 2018 12:35 pm
- Forum: Transmission
- Topic: Slipper pads or not?
- Replies: 6
- Views: 6816
Re: Slipper pads or not?
When they're installed, should they be greased? Weirdly the workshop manuals make no mention of them, nor are they shown in the exploded diagram of the clutch release mechanism...
- Fri Apr 06, 2018 12:12 pm
- Forum: Transmission
- Topic: Slipper pads or not?
- Replies: 6
- Views: 6816
Re: Slipper pads or not?
Cheers Charles, slipper pads have been ordered!
- Fri Apr 06, 2018 1:31 am
- Forum: Transmission
- Topic: Slipper pads or not?
- Replies: 6
- Views: 6816
Slipper pads or not?
Am I right in thinking that the two square slipper pads are missing here, or does this later bearing carrier not use them?